You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1241 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 5 posts

Saturday, February 26th 2011, 6:23pm

by Topher (Guest)

Interchangeable

Thanks for the input. Ill look into the swivel fittings, as it seem quite a bit less complex than setting up two complete delivery systems in the field.

Sunday, February 13th 2011, 2:49am

by Mitchgo

Swivel fittings make all your problems go away.
Hey there he is!!

Saturday, February 12th 2011, 11:16pm

by Kiril (Guest)

Swivel fittings make all your problems go away.

Tuesday, February 1st 2011, 2:11pm

by HooKooDooKu

I think your biggest issue is going to be finding a simple way to remove drip tubing.
From what I've seen, drip irrigation companies are not much into their systems being taken apart.

As an example, I once purchased some of the Rain Bird Easy Fit compression fittings:
http://www.sprinklerwarehouse.com/Rain-Bird-Sprinkler-Easy-Fit-Fittings-p/mdcfcoup.htm
They were super easy to connect. But the connections were permenant.

Now sure there are all sorts of swing joint assymblies, or just all types of fittings that allow you to connect drip tubing to standard pipe threads. But they are not easy to disconnect. Again, usually the fitting is designed to stay permenently attached to the hose. So at a minimum, you would have to unscrew all the connections each time.

Now the thing I found to make drip irrigation tubing easy to replace was this product as Lowe's:
http://www.lowes.com/pd_88290-1029-MLA-P2P_0__?productId=1103275&Ntt=drip+irrigation&pl=1&currentURL=%2Fpl__0__s%3FNtt%3Ddrip%2Birrigation
It is basically a drip fitting that screws onto the drip tubing (with the other side screwing into standard pipe threads). This made replaceing the drip tubing as easy as a few turns (one set to unscrew the old and a few more to screw on the new).

Now sure, you could say that that's all you have to do with any pipe threads. But with normal pipe threads, you have to take the time to use teflon tape to seal the connection. But this fitting didn't need tape ON THE DRIP TUBING side.

But this still isn't going to be an easy solution for you either, because the screw piece does work by having the screwn threads bite into the drip tubing. So sure it's good for a few cycles. But repeated use would quickly destroy the end of the drip tubing.


Of course, pretty much the same can be said for all the irrigation sprays. Nothing seems to really be made for quick change out. Sure things could be screwed and unscrewed, but that requires new teflon tape and time for each one.


Now the one idea I do have, depending upon your situation, is to maintain both drip and regular irrigation "IN THE FIELD". Basically, have the controller's supply water to an area, but once you get to the "area", use a Tee fitting and a pair of ball valves. One end of the Tee and ball valve would supply water to the drip tubing, while the other would supply water to the irrigation sprays. When you're ready to switch over from one to the other, you go out to these ball valves out at each of the zones and turn off one system and turn on the other. The basic idea is to have two fully functions systems, but rather than doubling the control valves and pipe to get from the valves to the zones, you use ball valves to share that part of the system.

Thursday, January 27th 2011, 10:28am

by Topher (Guest)

Interchangable water delivery (drip/sprinkler)

Im an installing a new irrigation system ~3acres for market veggie gardens, pasture grasses, and fruit trees. I'm tryiin gto think ahead about my operation and would like to pose a question. I plan to do a lot of crop rotation with those crops being watter either through drip or sprikler systems. I have the pressure and and flow to accomodate both in my differnt hydro zones and am installing irritrol adjustable pressure regulators on each zone so have control over each one.

My question - is there an easy/good way to predesign or install an interface that will allow me interchange my drip system with sprinklers as my crops rotate from year to year.

Thanks