You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 4638 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 9 posts

Thursday, May 11th 2006, 4:35am

by mburnickas

I just replace the complete unit since it is cheaper then the parts. Parts are $20 to $35 or $48 online for the complete unit.

But the price on the 860’s (as you posted) is the same I can find. Good price.

Tuesday, April 18th 2006, 9:42am

by browntiger

One can find RPZ Febco 860s for about $105 on internet

Monday, April 17th 2006, 3:43am

by Wet_Boots

Any backflow preventer will break when it freezes. Leave the water turned off until it's absolutely safe.

Monday, April 17th 2006, 2:40am

by SprinklerGuy

it won't happen again and again if you don't let it freeze. They make an insulated cover that will help during shoulder months....but truthfully.....leave it off until the possibility of 2 or more freezing nights is gone.

They make the plastic so it will absorb the damage....$49 is much cheaper than paying somebody 175-200 for replacement.

Good luck..

To answer your question...I don't know about the Watts....but most PVBs will have some plastic "disposable" parts inside for the same reasons.

Sunday, April 16th 2006, 6:15am

by Tom

Its plastic so the whole dang thing doesn't break, although its fairly common for one of the ball valves to split.

You could also insulate the pvb.

Sunday, April 16th 2006, 3:50am

by browntiger

I admit, I did turned it on prior to last winter storm.

But ... I don't understand why that part is made of thin plastic?
I could understand if gasket leaked. has the repair kit for about $49.

Plastic inside was so thin I see this happening again again....

So my question is Watts PVB plastiky on the inside?

Sould I just replace whole thing with RP

Saturday, April 15th 2006, 3:05am

by SprinklerGuy

I have found that the homeowners think it is the pressure that does this....ALMOST ALWAYS..they say "that new backflow valve you put in last spring exploded when I turned it on this spring"

Me: "Did you turn the system on after I winterized before today?"
Them: "NO...."
Me: "Really?"
Them: "Oh wait...I did turn it on back in February to water for about a week, but I turned it right back off"


BSME is right....the freezed damage doesn't always show up when you look at it....then when you ratchet that first ball valve open as fast as you can...hint ;) blows the already cracked and disconnected parts pretty high and it is VERY dangerous"

Friday, April 14th 2006, 11:21am


it probably had freeze damaage before you turned it on... I bet if you would have checked before hand it was already in pieces

Friday, April 14th 2006, 5:28am

by browntiger

Febco 765 1"

Is this just me or do they really suck.

Made of plastic parts on the inside,
our water pressure hit ~73 psi and febco exploded
catapulting bell (top part) about 10 ft.

Would Watts 1 800M4 FR be any better?