You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 468 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 7 posts

Tuesday, June 4th 2013, 10:08am

by pwps

Ah, I wasn't asked my location during the sign up process. I guess you have to go into your profile after the fact and update that info. But yeah, I'm in Centennial, CO. Just south of Denver.

Tuesday, June 4th 2013, 9:19am

by Wet_Boots

If you had included your location when you signed up, it would have become obvious. As it happens, your valve manifold is constructed with fittings used in systems that employ poly pipe, and I can see the grey plastic of insert fittings on the outlets of the two zone valves.

Tuesday, June 4th 2013, 9:04am

by pwps

Are polypipes fairly typical? This house is my first experience with an irrigation system and since it was previously installed I have no idea what they put down. I just assumed it was PVC pipe.

Monday, June 3rd 2013, 8:39pm

by Wet_Boots

You definitely have poly pipe in the zones, but don't sweat it. Trees do just about whatever they want to when it comes to roots causing damage.

Monday, June 3rd 2013, 8:03pm

by pwps

I did try the bleeder screws as well--same low pressure :(

I hope there are not polypipes in the ground. We bought our house 5 years ago and the previous owners had installed the system. I'm not sure what kind of lines he put down. I may do a little digging this weekend just to see.

I can check again this weekend for a leak. Yesterday I ran the zone for about 5 minutes or so and then shut it off to look for the leak. Maybe I should let it go a little longer.

I haven't noticed the seals leak or anything. I see if I can get my wife to help me with a couple of the heads.

Thanks for the input!

Monday, June 3rd 2013, 11:25am

by mrfixit

Try turning the valves on with the bleeder screw instead of the solenoid. Do they get full pressure that way? If so there's a problem with the valves.
--
So all four valves are in the same box. Both front and backyard valves. I was going to suggest that maybe someone closed a shut off valve somewhere but that would affect all four valves.
--
Unless you have polypipe installed in your yard it probably isn't tree roots.
--
I know you looked for break in the lines but maybe look again.
--
Do the sprinkler seals leak really bad? Could be you just need new sprinklers. Try pulling up two or more sprinklers at once and see if you can get them to seal. Yes you'll need really long arms or someone to help you.
--
Good luck!

Monday, June 3rd 2013, 9:47am

by pwps

Two front zones have low pressure

I have a Rainbird system with 4 zones: 2 in front and 2 in
back. Each zone has between 5-6 heads. The 2 zones in back work just fine. The 2
zones in front are the issue—the pressure has dropped recently. When each of
the front zones is on, a couple of the heads pop up and put out a little water while most of the other heads
don’t pop up at all. The ones that don’t pop up still put out water. And on the
ones that don’t pop up, if I manually pull them up, they just drop right back
down when I let go.

I tried to test this weekend for any leaks. I ran each zone
for several minutes but didn’t see any obvious wet spots. I also ran each zone
manually via turning the solenoid and still saw the same low pressure. So my
next guess is a tree root. Before I go digging up my yard, I just want to make
sure there’s nothing obvious that I’m missing. Is it still possible that it
could be a simple replacement of the two valves and/or solenoids? Thanks for any help!


Just for visual aid, here’s my valve control box (the water is from opening the bleed screws):