You are not logged in.

  • Login
  • Register

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 561 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Thursday, November 10th 2011, 11:02am

by Wet_Boots

You can always go the 5-piece route. Start with a female coupling in place of the original head. Then a MPT x swing-pipe elbow. Then the swing pipe. Another MPT x swing-pipe elbow. A marlex elbow (because you are not a hack) ~ Job done.

Thursday, November 10th 2011, 5:47am

by Jasper

If you are not on swing pipe, now would be a good time to do so:

http://www.sprinklerwarehouse.com/Hunter-Swing-Joints-s/224.htm



Or you could just go to the reduction nipples and forego having to manufacture or buy swing joints, or purchase a reduction bushing and a riser.



Of course you can always install the 2" Orbits @ .99 to ease positioning the head to grade ( :rolleyes: joking).



Post a picture for better advice.

Wednesday, November 9th 2011, 11:46pm

by Mitchgo

More then likely it's a 3/4 marlex or male swing elbow.

You can cut that out and install a 1/2 swing fitting. Or go boots route- however your head probably be sticking out of the ground

Wednesday, November 9th 2011, 11:18pm

by mrfixit

No Dog those wont work. Here's what you need.

www.sprinklerwarehouse.com/Dura-PVC-Threaded-Reducing-Bushing-p/439-101.htm

Unscrew the 3/4 inch risers, insert bushing. Use teflon tape. Buy some 1/2 risers.

Wednesday, November 9th 2011, 5:12pm

by bigdogmedia1966

would this work

Brass Fitting

Wednesday, November 9th 2011, 3:17pm

by Jasper

Quoted from "mrfixit"

Hey Jasper, I was wondering if you're connected to the Flex PVC site? What I'm after is the 1" flex PVC. I don't need a ROLL of flex pvc. I need straight pieces. 48" in length would be good. I'll buy 100 feet if neccessary. I already have a 100 ft. roll I hate. I have 1/2 and 3/4 in my stock. I'm having trouble finding 1". Thanks!
Sorry, no I'm not connected with flexpvc.com. I posted the links to help the original poster get an idea what to look for. I usually get my materials from a local outlet (not Home D or lowes... GACK).

Wednesday, November 9th 2011, 2:10pm

by mrfixit

Hey Jasper, I was wondering if you're connected to the Flex PVC site? What I'm after is the 1" flex PVC. I don't need a ROLL of flex pvc. I need straight pieces. 48" in length would be good. I'll buy 100 feet if neccessary. I already have a 100 ft. roll I hate. I have 1/2 and 3/4 in my stock. I'm having trouble finding 1". Thanks!

Wednesday, November 9th 2011, 5:39am

by Jasper

Try reduction nipples found here: http://flexpvc.com/cart/agora.cgi?cart_id=5036647.5029&product=PVC-Nipples-Reducing-TBE



Or these reduction bushings: http://flexpvc.com/cart/agora.cgi?cart_id=5036647.5029&product=PVC-Reducer-Bushings-MPT



Or, if your mist heads are on swing (funny) pipe; remove the existing male 3/4 funny elbow and replace with male 1/2 elbow.



Hunter MP's usually require an adjustment in run time to produce adequate percipitation. Use the chart found here to determine appropriate run times: http://www.hunterindustries.com/products/mprotator/

Tuesday, November 8th 2011, 5:39pm

by Wet_Boots

There do exist 1/2-inch MPT x 3/4-inch FPT adapters, but they aren't standard issue

Monday, November 7th 2011, 6:20pm

by bigdogmedia1966

Sprinkler body adapter

I 'm changing my K Rain sprinklers for Hunter PRS40 with MP Rotator Nozzles and the K Rain is 3/4" inlet VS. Hunter is 1/2". Is there an adapter that I can use to reduce to 1/2"?