You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2567 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 5 posts

Thursday, April 5th 2007, 3:58pm

by madisonvfd

I also have 3 heads that are dribbling, one of which I just replaced today. If the valve feeding it is clogged with debris then it can't shut off completely, hence the dribbling? How come just some are dribbling and others aren't on that same line?

Sunday, August 13th 2006, 5:08am

by bethany

Thanks, I figured out that after and found a filter set up from vuflow on sprinkler warehouse's web site and purchased it.The screen they recommend though is a 60 mesh.Is this fine enough? I'll find out when I install it.I also bought 2 new valves which should be a pleasure to install since the guy who installed the box made it so tight I have to dig up the box around the valves.What an idiot!![:(!] <blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote"><i>Originally posted by Wet_Boots</i>
<br />The water supply to the system should be run through a 100 mesh strainer, to keep particles in the water from fouling the valves.
<hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">

Sunday, August 13th 2006, 2:11am

by mrfixit

Hi there, If you have debris in water line or in the valve then the new diaphrams may be ruined already. If you see a pit in the rubber then it's bad. You may also have particles stuck to them. Next time you take the valve apart try flushing the line. I agree with Boots that you need a filter. It's a must really. Also, the seat, which is the part the diaphragm pushes against when the valve shuts off might be pitted from sand or rocks. Small pits can be sanded down easily with a fine grain wet sandpaper and the valve will shut off completely. Large pits or a hairline crack. You're out of luck. Only replacing the valve will help. One more thing. I have on a rare occasion seen a piece of something stuck to the bottom of the plunger inside the solenoid making the valve leak. Being you're on a well for sure check that. Good luck!

Saturday, August 12th 2006, 5:57pm

by Wet_Boots

The water supply to the system should be run through a 100 mesh strainer, to keep particles in the water from fouling the valves.

Saturday, August 12th 2006, 3:50pm

by bethany

Dribbling Heads

I have a 8 zone system that runs raw well water through it.I can't seem to figure out why I have two heads in two different zones that continue to dribble even after the cycles are over.The leaking is so much that it has left major wet spots in the lawn. I have tried changing the diaphrams in the valves and still no help.
I have irritol 2400T globe valves and hunter pgp heads.I can't seem to find the selonoid parts for the irritol valves.
Somebody please help! I had to shut down the whole system just to dry out the lawn.