You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1415 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Thursday, October 7th 2010, 9:06pm

by Wet_Boots

Electric zone valves do nothing to prevent water from flowing thought them in reverse, so no, they would not serve as check valves.

Thursday, October 7th 2010, 7:42am

by mxquattro (Guest)

OK Got it, thank you. It sounds like if I wanted though, I can use an electric valve at each sprinkler head too. Of course it wouldnt make sense to due to cost, but seems feasible. I think i have a grasp on what I need now, thank you everyone.

Wednesday, October 6th 2010, 4:04pm

by HooKooDooKu

thanks for that clarification. I assume I use one or the other right? Would never need both?


Check valves are devices that allow water to only flow in one direction. If you don't want the irrigation pipes to drain out the lowest spray head when the system is turned off, you install check valves under each and every spray head.

Electric valves are simple On/Off valves that allow you to start/stop the irrigation system using an electronic controller. If you plan on having someone manually turn the water on/off, you don't need electric valves. If you want to be able to set the system to automatically turn on, you'll want electric valves.

Wednesday, October 6th 2010, 11:04am

by Wet_Boots

If the system runs from a controller, you will have an electric valve - the individual check valves would be what prevents low-head drainage. (although I do wonder why level ground isn't being chosen for this project)

Tuesday, October 5th 2010, 9:18pm

by mxquattro (Guest)

thanks for that clarification. I assume I use one or the other right? Would never need both?

Tuesday, October 5th 2010, 10:28am

by Wet_Boots

There are no "electric check valves" per se. You have electric valves. You have check valves. Two separate items. Little plastic check valves can be had, to thread onto 1/2-inch pipe threads, one for each nozzle.

Sunday, October 3rd 2010, 4:17pm

by mxquattro (Guest)

Hi wet_boots. I think youre right about having it on both sides, I may have to consider that. We were leaning toward an electric type solenoid check valve underneath vs one in the head. we were trying to avoid popup heads altogether since this is going to be for cold weather testing, and if we have freezing rain or something, we still want them to spray and not be stuck in ice and not pop up. We will be spraying for 15 seconds a shot every hour or so, so there wont be a lot of run off I hope. If so we can adjust the time. but yes, we do want even spray coverage.
Are there electric check valves on this site? (sprinklerwarehouse.com) I cant say as I saw any. Id love one to fit in the 6" round valve box that was recommended to me.

Sunday, October 3rd 2010, 10:01am

by Wet_Boots

If you want even watering (do you?) then you will have nozzles on both sides of the strip. If this is laid on a slope, then the water will drain from the low heads. you can deal with this by installing check valves under each nozzle, in the plumbing connecting the nozzle adapter. It could be that by the time you buy check valves and nozzle adapters, you'd be better off using small popup heads with check valves built in.

-

Is overspray an issue? Assuming the antifreeze cost money, I would expect so.

Friday, October 1st 2010, 7:46pm

by mxquattro (Guest)

Just when I thought I couldnt get more confused. I just went to order all my parts and holy cow there are a ton of options. It looks like I might need help with that too.. It seems I have to get the nozzle separate from the body? Since Im putting them on boxes, I dont need/want pop ups. Its a strip about 12' wide and 50' long and on a slight hill. I want to put nozzles only on one side so Im thinking 180 degree pattern maybe 10 feet apart and ill need an electric (I would guess) solenoid to prevent siphoning when off. Im definitely getting the boxes with covers like suggested above. Make sense or am I missing something? Thank you!

Friday, October 1st 2010, 1:35pm

by mxquattro (Guest)

No wet_boots, having 3 or 4 24" boxes with sprinkler heads on them is fine. But having piping between them above ground wouldnt be. Location isnt flexible, we are just trying to minimize issues.